Search results

I installed bushwhacker fenders and led turn signals a while back. The turned signals work as I expected. I was running a diagnostic for another issue and got the following two codes - B17C1-11 and B17BC-11. RIGHT AND LEFT sidemarker lamp control circuit short to ground. I’m guessing that...

So I finally got my new multimeter to measure parasitic draw. It came in at 0.088 Amps. - the Jeep had been sleeping for about 4 hours before testing, and the keys are all in faraday boxes. I disconnected all my accessories, no change. I disconnected the cabin lighter ,because I have LasFit...

Oops I should read more.

Anyone installed the Z Automotive Nozlimitz and used the security enclosure? I can’t find any instructions on where to mount it or what actually goes inside the box. I’m assuming just the module, and not the actual canBus. Any pictures of an install would be helpful. I sent an email to Z...

My wife hid 73 ducks all around the house, found 72…..

I installed a midland 275, with the magnetic antenna mount and the 32” MXTA26. I’m using an swr meter and getting 1.74 reading. No matter where I put the antenna- on the ground, on the ground on a steel plate, on the Jeep. Etc. I’m using the sw33 surecom meter, cause I had that available. If...

For absolutely no sane reason at all, I decided to install the mishimoto intercooler pipe with a turbosmart plumb back valve. I’ve seen installs on the turbosmart purge to atmosphere, but not the plumb back. I reached out to turbosmart, but they said the valve can only line up one way. Which is...

Anyone know what this is. Just showed up on my garage floor. Jeep / Nissan or tool possibly rivet. It it food except byy the flange.

My JScan app says it needs to be updated, and won’t load on my iPhone. It won’t update, I get a try again later. Anyone else experiencing this?

I bought this for $125 on eBay back in January. It is one of the better quality aluminum expansion tanks. It is an Kokshely part number KK05006. Apparently now they are $80 on Amazon. I’d go zero dollars , you pay shipping. Never installed, in new condition. I got the mishimoto one and want...

Besides noticing that I need to trim my fender liners to allow for better travel on the Autolynx, (after yesterday’s run) upon driving 35 miles home, my Autolynx had not “snapped” back into its home position. I had to manually manipulate the sway bar to snap it back into normal connected mode...

I have a 2022 Willy’s with the Dana M186 Front axle. I’m using the Apex disconnect and AAL fender liners. When not disconnected, I have no issues with the Apex rubbing on anything. I have 1.5” spacers, so no wheel rubbing. However, today I was flexing a bit more than usual and noticed the apex...

Just a few Pictures and Install Tips for the 2.0T. Remove the C1 ECU Plug from the front of the Jeep as per Instructions. Just push the bar gently forward. Use some WD-40 and gentle rocking motion to help it disconnnect . First cut the zip tie holding the wires to the top of the connector...

Anyone with experience on removing the cover from the ECU plug on the 2.0? I haven’t really tried yet, but I could not see any simple way right out of the gate. any advice is appreciated. Looks like maybe it separates in the middle by prying it apart. Starting to prep for my rpm extreme...

So installed the Grimm off road. On board air, which puts the switch in the engine bay. After off roading, it was super dusty, so I covered the battery and fuse box and gently put a hose on the engine bay, whoops, hit the compressor switch, and later that day, before it was dry, tried to use the...

Jeep doesn’t understand that we are celebrating 249 years, as 250 years as the USA would be 2026. I know we had that great parade celebrating the army’s 250 years. But the declaration of independence was 1776.

So I planned an easy trip with my better half for today. It was to be an easy trail to get her into wheeling. Packed everything we would need for just about any scenario. Did the air down, released the front sway bars and set off on the trail. We got about 1/2 mile to the first switch back and...

So my new steel bumper comes with LED fog lights. Old plastic bumper had LED fog lights. It is a Willy’s. The new bumper has a 12 pin connector to plug into the body of the Jeep, which has a 4 pin connector. The wires seem to be the same ground, white with orange, white with yellow. Can I...

I thought I had my brakes all figured out after I mixed up the rear caliper brackets, but I still have doubts. I need one brave soul with Hd brakes to pull out their driver side rear lower caliper slider pin and post a picture for me. This can be done without removing the wheel, just the one...

long Story, so I’ll cut to the chase. I have two rear caliper brackets, and don’t know which goes to which side. They appear identical, but I’m sure they are side specific. Only difference I can see is on is stamped 2132, and the other is 2123. Any ideas on how to determine driver versus...