Billy
Well-Known Member
Yeah, that's what we all want. An external release to eject the doors...Imagine if the fender air vent/duct doubles as a release/handle for the removable doors ...
:cwl::cwl::cwl::cwl:
Sponsored
Yeah, that's what we all want. An external release to eject the doors...Imagine if the fender air vent/duct doubles as a release/handle for the removable doors ...
OH MY GOD, WHAT A MALL CRAWLER!!!!!!!!Lots of changes. For example, the 4 round air vents now line up left to right, with the center ones being on each side of the radio (instead of below the radio).
Imagine the YouTube videos and subsequent memes tho ....Sorry but that makes no sense. The hinges are what keep the doors on and there's still two of them per door. I'm not sure I'd want to drive around with some "quick release" button or handle mechanism that unlatches your doors in an instant. Imagine if it malfunctions or is inadvertently engaged while driving.
While I'm dissapointed the hinges are still exposed to rocks/chips, they aren't that difficult to remove. Though I would prefer they improve the tab/clip connectors for the wire looms, they can be a bit of a pain sometimes, and there are so many ways they could be easier and tool-free.But in all seriousness, I hope these doors come off easier and quicker than the JK
So you don't have 2 minutes out of your day to take off your doors? Like I've said before if you want doors that come off/slide open with the push of a button buy a Minivan.Imagine the YouTube videos and subsequent memes tho ....
But in all seriousness, I hope these doors come off easier and quicker than the JK
Hahahahaha fall backSo you don't have 2 minutes out of your day to take off your doors? Like I've said before if you want doors that come off/slide open with the push of a button buy a Minivan.
Are you suggesting they move it somewhere or keep it covered? The hinges that is. I think either would be met with complaints.While I'm dissapointed the hinges are still exposed to rocks/chips, they aren't that difficult to remove. Though I would prefer they improve the tab/clip connectors for the wire looms, they can be a bit of a pain sometimes, and there are so many ways they could be easier and tool-free.
But most importantly, hopefully a sprinkle of Aluminium in the doors will make them a bit lighter for maneuvering and storage.
Yeah, I'm saying they should update the design, especially for the rear.Are you suggesting they move it somewhere or keep it covered? The hinges that is. I think either would be met with complaints.
What I'm saying is most Wrangler owners like the exposed hinges, even if they are vulnerable to rock chips and the like. Moving the hinges will see a chorus of pitchfork cries of "no longer a Jeep!" It's an easy fix for most and sometimes just user error from people running wide tires who should have used mud flaps or hinge covers when offroading.Yeah, I'm saying they should update the design, especially for the rear.
Everything is met with complaints, do or don't, technically mine is a complaint (or hope for,an improvement). However I doubt it would rank high on the list of must-haves the way solid axles, sports bar, removabke doors, manual transmission, 7-slot grill, etc. would. In fact if it was done with this generation I would expect those complaints to be overshadowed by those that are currently being prepared for the fender-mounted turn signals and DRLs.
It looks like they've reduced the size/profile of the hinges, so obviously a step in that direction.
Yeah, I use ACE engineering rails ontop of the Rubi Rails to mitigate it on the old Rubi and now Aspen-X, but it is an anoyance on the cottage Wrangler which is a bare bones build with 17" wheels and Connectivity+430, but manaual everything else, so it gets 3M tape, but on a hinge it requiresa bunch of re-application.What I'm saying is most Wrangler owners like the exposed hinges, even if they are vulnerable to rock chips and the like. Moving the hinges will see a chorus of pitchfork cries of "no longer a Jeep!" It's an easy fix for most and sometimes just user error from people running wide tires who should have used mud flaps or hinge covers when offroading.
Yeah, that's definitely a bigger problem as the interior bushings wear out even within a single summer/season. This will be more of an issue if this is a junction point for Aluminium and Steel, as in the Defender that caused massive corrosion issues because of the lack of insulating isolation material. If they put a plasticky 'teflon-y' shroud sleev in there it would likely hold up better, although might swing to easily and increase the number of door removal mishaps initially from people expecting the swing rate/intertia of the current design.My greater concern with the hinges is the wear and tear experienced when the doors come on and off often.
Halo lights look nice. Very bright even through the camouflage.Yes, halo rings have been seen on already. See latest -- http://www.jlwranglerforums.com/for...gler-rubicon-and-sahara-jlu-roof-exposed.698/
Here's a look:
My guess is this will likely remain "an issue" in the JL since it's inherent in the functionality of the doors as safety/protection first rather than a part that should be designed to be as easily and frequently removed as possible. They can provide stronger more durable bushings but that is not going to fix all the problems either as there is just unavoidable wear and tear when constantly bolting/unbolting something so heavy/rigid. And as you said moving to aluminum interior door panels poses another set of problems potentially.Yeah, I use ACE engineering rails ontop of the Rubi Rails to mitigate it on the old Rubi and now Aspen-X, but it is an anoyance on the cottage Wrangler which is a bare bones build with 17" wheels and Connectivity+430, but manaual everything else, so it gets 3M tape, but on a hinge it requiresa bunch of re-application.
Yes it's just another issue on the proverbial 'list,' and like all of them there is always someone ready with a pitchfork, even if it's really not at the heart of a Jeep (since the Willys was sans doors anyways) but once things like the axles, roll-cage, etc make their way in then people's outrage move from the significant to the minor aesthetics as a hill-to-die-on 'crucial Jeep aspect'.
Yeah, that's definitely a bigger problem as the interior bushings wear out even within a single summer/season. This will be more of an issue if this is a junction point for Aluminium and Steel, as in the Defender that caused massive corrosion issues because of the lack of insulating isolation material. If they put a plasticky 'teflon-y' shroud sleev in there it would likely hold up better, although might swing to easily and increase the number of door removal mishaps initially from people expecting the swing rate/intertia of the current design.
I also wonder about how the hinges themselves will hold up either if they are aluminium possibly like the door, or if they are the steel attached to the aluminium door moving the al-fe interaction point from the moving hinge itself to the attach point.